For iti jobs, iti fitter, Fitter iti, Iti mcq, Iti online exam, Iti course, Lathe chapter, iti govt job, Iti fitter government job, iti ka full form, Fitter meaning in hindi, What iti course, Iti kya hai, iti course list, Iti fitter question paper, Iti fitter syllabus, Iti fitter multiple choice questions paper with answers pdf, Iti fitter question paper pdf free download, Iti fitter government job, Iti fitter question paper.
Iti Fitter Multiple Choice Questions Paper With Answers Pdf Lathe Chapter
Important Lathe Chapter Multiple Choice Questions For Iti Jobs
For iti jobs
1. The size of three jaw chuck is specified by
A. Width of the body of the chuck
B. The diameter of the body of the chuck
C. The thickness of each jaw
D. The size of each jaw
2. Dead centre compared with the live centre, bears or resist
A. Equal friction
B. Non friction
C. Less friction
D. More friction
3. When the tailstock is offset for taper turning, the centre line of the tailstock is
A. Inclined with the lathe bed at an angle equal to the angle of taper required
B. Inclined with the lathe bed one half of the angle of taper required
C. Still parallel with the lathe bed
D. Either a or b
For iti jobs
4. Which one of the following controls the length of taper cut the compound slide method
A. Tailstock
B. Top slide
C. Cross slide
D. Saddle
5. For calculations of offset, we should consider
A. Total length of job
B. Length on which taper is required
C. Diameter of the job
D. Both a and b
6. By taper turning attachment, taper can be cut on any workpiece which is held
A. In a chuck
B. Between centres
C. Neither a or b
D. Either a or b
7. The chip breaker on a lathe tool is essential when
A. Turning hardened materials
B. Turning cast iron
C. Turning ductile materials and to break the chips
D. Turning soft material
8. Which one of the following is used only for for finishing and maintaining correct form of thread
A. Tap
B. Threding tool
C. Threading chaser
D. Tipped tool
9. Lathe Machine bed is made of
A. High alloy steel
B. High carbon steel
C. Cast iron
D. Mild steel
10. lathe Machine half centre is used
A. To face the workpiece upto the end of the centre hole
B. To turn long workpiece
C. Because it is easy to lubricant the workpiece
D. To support the workpiece always
For iti jobs
Iti Fitter Multiple Choice Questions Paper With Answers Pdf Lathe Chapter Download Pdf >CLICKHERE<
Lathe Chapter Multiple Choice Questions For Iti Online Exam
Iti Online Exam
11. Mechanism of back gear is provided in cone pulley headstock to
A. Reduces the speed of spindle
B. Increase the speed of spindle
C. Reverse the speed of spindle
D. Transmit power from spindle gear to stud gear
12. The negative rake angle is generally provided on the tool made of
A. High carbon steel
B. Tungsten carbide
C. Tool steel
D. High speed steel
13. While drilling in lathe, the drill is held in the
A. Bed
B. Compound rest
C. Tailstock
D. Headstock
14. The included angle of live centre nose is
A. 30°
B. 45°
C. 60°
D. 90°
15. Which among the following centres is suitable when workpiece held between centres is to be turned at high speed
A. Revolving centre
B. Pipe centre
C. Half centre
D. Ball centre
16. Which one of the following is used to hold workpiece for machining diameter concentric to its hole
A. Faceplate
B. Mandrel
C. Three jaw chuck
D. Four jaw chuck
17. Which among the following taper turning methods is used for cutting steep taper
A. Set over method
B. Taper turning attachment
C. Form tool
18. Which one of the following centres is suitable while cutting taper by set over method
A. Revolving centre
B. Ball centre
C. Half centre
D. Plain centre
19. In a gap bed lathe, the gap is provided
A. Just below the spindle of the tailstock
B. Just below the nose of the headstock spindle
C. Anywhere in the bed
D. In the middle of the bed
20. Tumbler gear quadrant is used for
A. Increasing the speed of the spindle
B. Decrease the speed of the spindle
C. Changing the direction of rotation of the lead screw
D. Changing the direction of the spindle
Iti Online Exam
Lathe Chapter Multiple Choice Questions For Iti Online Exam Download Pdf >CLICKHERE<
Iti Fitter Syllabus Lathe Chapter For Iti Govt Job
Iti Fitter Syllabus, Iti Govt Job
21. A faceplate is held at
A. Tool post
B. Tailstock
C. Headstock
D. Bed
22. Which one of the following tool angle is provided to avoid rubbing of the body of the tool with the workpiece
A. Helix angle
B. Clearance angle
C. Rake angle
D. None of the above
23. The horizontal feed, cross feed and screw cutting movement in a lathe is controlled by
A. Apron
B. Cross slide
C. Tailstock
D. Headstock
24. The headstock of a lathe is situated at the
A. Bottom of the lathe bed
B. Middle of the lathe bed
C. Left hand end of the lathe bed
D. Right hand end of the lathe bed
25. Which one of the following is not a part of the centre lathe
A. Lead screw
B. Arbor
C. Feed rod
D. Saddle
26. Which one of the following is used to hold cylindrical rough casting for turning
A. Magnetic chuck
B. Collet chuck
C. Four jaw chuck
D. Three jaw chuck
27. Which taper is used on spindle nose of the lathe head stock
A. Morse taper
B. Pin taper
C. Brown and sharp taper
D. Jarno taper
28. An irregularly shaped workpiece is turned on a lathe. Which work holding accessories is used
A. Faceplate
B. Driving plate
C. Two jaw chuck
D. Three jaw chuck
29. The taper provided in the nose of the tailstock barrel is
A. Morse taper
B. Jarno taper
C. Brown and sharp
D. Metric taper
30. A tool, which is used to enlarge a previously drilled hole is known as
A. Boring tool
B. Form tool
C. Turning tool
D. Facing tool
Iti Fitter Syllabus, Iti Govt Job
Iti Fitter Syllabus Lathe Chapter For Iti Govt Job Download Pdf >CLICKHERE<
Fitter Iti Lathe Chapter Multiple Choice Questions Answer With Pdf
Fitter iti
31. Follower steady is fixed on the
A. Tailstock
B. Bed
C. Saddle
D. Headstock
32. A follower steady consist of
A. One pad
B. Two pads
C. Three pads
D. Four pads
33. While using the form 5ool method of taper turning
A. Carriage is to be locked
B. Compound rest is to be locked
C. Top slide is to be locked
D. Tailstock is to be locked
34. Which one of the following shoulders is used on component to be threaded
A. Beveled shoulder
B. Undercut shoulder
C. Radius shoulder
D. Square shoulder
35. Which among the following factors governs the selection of feed when turning a workpiece
A. Tool geometry
B. Surfaces finish required
C. Type of coolant required
D. All of the above
36. Scroll and gear mechanism is employed in
A. Collet chuck
B. Magnetic chuck
C. Four jaw chuck
D. Three jaw chuck
37. An angular workpiece is to be faced. It should be mounted
A. In a collet
B. Three jaw chuck
C. On a face plate
D. Between centres
38. A tumbler gear unit consists of
A. Four gears
B. Three gears
C. Two gears
D. One gear
39. In an open side tool post
A. Single tool post is held with 3 bolts
B. Single tool is held with 1 bolts
C. Two tools are held with 3 bolt
D. Two tools are held with 1 bolt
40. Which one of the following tool post is easy for setting the tool centre height of the tool in a lathe
A. Universal tool post
B. Four way tool post
C. Single screw tool post
D. Open side tool post
Fitter iti
Fitter Iti Lathe Chapter Multiple Choice Questions Answer With Pdf Download >CLICKHERE<
Lathe Chapter Previous Questions For Iti Fitter Technician
Previous Questions For Iti Fitter Technician
41. Which one of the following materials is used for manufacturing centre drills
A. Cast iron
B. High speed steel
C. Mild steel
D. Cast steel
42. Which one of the following taper is used for making shank of lathe centre
A. Morse standard taper
B. Brown and Sharpe taper
C. Jarno taper
D. Non standard taper
43. Which one of the following on a lathe is used to give depth of cut
A. Cross slide
B. By adjusting the tool
C. Top slide
D. Compound slide
44. The sliding surface of the lathe bed are
A. Flame hardened
B. Case hardened
C. Normalised
D. Tempered
45. Which one of the following types of chips is found while turning cast iron
A. Long curly chips
B. Segmental chips
C. I shaped chips
D. Spiral chips
Previous Questions For Iti Fitter Technician
Lathe Chapter Previous Questions For Iti Fitter Technician Download Pdf >CLICKHERE<
Iti fitter multiple choice questions lathe chapter part 1 SINGLE PDF (ALL IN 1PDF) DOWNLOAD >CLICKHERE<
Lathe Chapter 2 👉>>CLICKHERE<<
THIS ARTICLE ALSO ANSWERS THE FOLLOWING SEARCH QUERIES BELOW:
ITI FITTER APPRENTICESHIP, ITI FITTER BOOKS IN HINDI, ITI FITTER SALARY, ITI FITTER PRIVATE JOB, ITI FITTER FRESHER JOB, ITI FITTER VACANCY, ITI FITTER RAILWAY JOBS, ITI FITTER QUESTION, ITI FITTER TOOLS, ITI FITTER 3RD SEMESTER QUESTION PAPER, ITI FITTER MCQ, ITI FITTER SUBJECT, ITI FITTER QUIZ, ITI FITTER THEORY BOOK, ITI FITTER BOOK PDF, ITI FITTER INTERVIEW QUESTIONS, ITI FITTER QUESTION BANK, ITI FITTER TRADE JOB, ITI FITTER OBJECTIVE BOOK PDF, ITI FITTER OBJECTIVE QUESTIONS, ITI FITTER MCQ PDF, ITI FITTER OBJECTIVE BOOK, ITI FITTER PREVIOUS YEAR QUESTION PAPER, ITI FITTER QUESTION PAPER PDF.
READ MORE:
- Iti fitter multiple choice questions cutting tools and operation chapter part 1
- Iti fitter multiple choice questions measurement and measuring tools chapter
- Famous Places In India – Important GK Quiz Questions And Answers For Competitive Exams, Download Pdf